SLING COMPARISON CHART

Twin-Path® Slings
with Covermax®
Cover and K-Spec®
Core Yarn
Polyester
Roundsling
Nylon Web
Sling
Polyester
Web Sling
Wire Rope
Sling
Tri-Flex® Sling
(3 part)
Multi-Part Wire
Rope (Gator
Laid® and Gator-
Flex® Slings)
Chain Sling
Key Features Lightest and Strongest Slings available, Repairable, Overload Indicators, Low stretch, Longest lasting Sling Low cost flexible lifting sling, available with Check-Fast® Inspection and
Covermax® Cover
Low Cost general
purpose lifting sling
Low Cost general
purpose lifting sling
Low Cost general purpose lifting sling Flexible, more ergonomic, cost
effective alternative to Wire Rope Sling
Flexible, more ergonomic, cost effective alternative
to Wire Rope Sling,
low D/d ratio
Heavy duty, repairable Sling
Approx. Weight to WLL ratio 1lb/40,000lbs 1lb/15,000lbs 1lb/15,000lbs 1lb/15,000lbs 1lb/10,000lbs 1lb/7,500lbs 1lb/9,000lbs 1lb/5,000lbs
Length Tolerance +/- 1" Call Call Call +/- diameter of rope +/- finished diameter of rope +/- finished diameter of rope +/- length of one link
Stretch at WLL <1% 3% 6-10% 3-4% 1% 1% 1% <1%
Max Temp 180 180 180 180 400 400 400 400
Flexibility Very Flexible Very Flexible Very Flexible Very Flexible Low Flexible Flexible Flexible
UV Degradation Low Low to High High Moderate N/A N/A N/A N/A
Abrasion Resistant High Low to High Low Low Very High Very High Very High Very High
Proof Tested Yes No No No No No No Yes
Repairable Yes No No No No No No Yes
Design Factor 5:1 5:1 5:1 5:1 5:1 5:1 5:1 4:1
D/d Ratio in
eye
N/A N/A N/A N/A 5:1 1.5:1 1:1 N/A
D/d Ratio in body Any comparably rated
fitting
1:1 N/A N/A 25:1 5:1 5:1 6:1
Resistance to Acids Very Good Good Poor Good Good Good Good Good
Resistant to
Salt Water
Yes Yes No Yes No No No No

Frequently Asked Questions

What is the OSHA standard for slings?

The OSHA standard for slings is outlined in 29 CFR 1910.184, which establishes safety requirements for the use, inspection, and maintenance of all types of slings used in general industry. It specifies that slings must be visually inspected before each use by a competent person and removed from service immediately if damaged or defective. The standard prohibits shortening slings with knots, bolts, or other makeshift devices and forbids loading a sling beyond its rated capacity. Additionally, slings must be properly protected from sharp edges and heat damage, and must display legible identification tags indicating material type, rated load, and manufacturer information.


What is the ideal sling angle?

The ideal sling angle is a 90 degree angle vertical hitch, where the sling legs lift straight up-and-down and no angle tension is added. As the sling legs spread out, the angle creates extra tension and the sling must be derated. Lower angles increase tension quickly, so riggers try to keep sling angles high and avoid shallow angles that can overload the sling and hardware.


What are the rules for lifting slings?

The rules for lifting slings emphasize proper use, inspection, and load control. These rules depend on sling material and manufacturer. Slings must always be used within their rated working load limits (WLL), taking into account the type of hitch (vertical, basket, or choker) and the angle of use. Rigging personnel must inspect slings before each use for signs of wear, cuts, broken strands, kinks, or other forms of damage, and defective slings must be immediately removed from service. Slings should never be twisted, knotted, or used around sharp edges without adequate padding. Loads must be balanced and securely attached, with all personnel staying clear of suspended loads to avoid injury. Proper sling selection, correct hitching methods, and attention to load stability are key to maintaining safety and compliance with OSHA standards. Always follow the sling manufacturers guidelines while using lifting slings.